IHC Visual Controller 3 incl. antenna. The controller is designed for use in building services, including lighting control, monitoring, alarm system and thermal management. In IHC controller gets the information from the connected signal generators worked. This can result in an on or off switch, timer function, a flasher, a dimmer signal etc., depending on the programming. To obtain function carried forwarded information to the actuators, which activate the desired appliances.

IHC Control alarm keypad IP55. The keypad is specially designed for IHC Control Alarm concept. The keyboard, for example. is used for activation and deactivation of the alarm from the outside, past the coupler in which bypasses the zone or the activation and deactivation of an electromagnetic door lock. These functions programmed in IHC controller. Can be mounted directly on the door frame, on an outside wall or on a flush box FUGA 2 module. Note: TermIHC Controller can not be used with IHC Control Alarm concept.

adhesive pad softline - wireless - 1 module - silver

IHC Control Modem SMS modem. To monitor and control the IHC input and output modules using SMS messages over the GSM network. SMS module can be used both in small systems as Stand alone, ie without an IHC controller and IHC Control systems with an IHC Controller with Viewer. The modem can also send text message by power outages. In Stand alone operation includes modem management to make thermal management based on SMS messages. So that it can be used as inexpensive system for remote control and monitoring of eg heat in the cottage.

IHC Control input 24 V DC 24mA with 16 inputs. Used to collect the signals from the low-current switches, such as pressure control relatives, thermostats, and the like. To IHC system can be considered a low voltage system, it is a requirement that the used switches are insulated to double-insulation (8 mm creepage distance) relative to the 230 / 400V network. It is possible to place the input module 24 both centrally at the Controller and a decentralized, distributed in the installation.

IHC Control Output 400 V AC 8X10A with 8 outputs. Used for coupling of 8 pieces. 230 V a.c. loads controlled by IHC system.

Product: IR-PD-DALI (92094) With infrared remote control LUXOMAT® IR-PD-DALI all settings can be conveniently carried out from the ground, without cumbersome set of ladders. It is suitable for lofts motion detectors: LUXOMAT® PD2-M-DALI / DSI and PD4-M-DALI-DSI. Through various programs can motion sensor to be tailored to individual requirements, even after installation. Additional features such as. autoloading in the current daylight value or the useful 2 sec.-test function can be performed with IR-PD-DALI, which can be ordered as an option. The light can be switched on or off by pressing a key. A further installation of a switch is thus not necessary. A practical wall bracket (dimensions (approx): 63 x 29 x 19mm). Battery: Lithium CR2032 - 3 Volt (included) Range (around) m: depending on lighting conditions - cloudy or dark: 5 to 6 m direct sunshine: 2 to 3m. Dimensions: L 80 x W 60 x H8mm

IHC Wireless Battery Press accessories adhesive pad Baseline 1modul.Anvendes when the battery pressure mounted on glass surfaces. Comes in a bag with 5 pieces.

IHCWireless for incorporation Input 1-4 channel. Used for installation in products to be able to send input to IHC Wireless system. The transmitter is battery operated and can be connected to up to four pressure. Both short and long pressures can is transmitted (eg. By dimming) . Continually signals from, for example. one NC contact should not be used on the transmitter. The transmitter can be used for LK Wireless stand-alone or with IHC Control.

IHC Control cabel USB-RS232 converter for communication IHC Visual 1 and PC

IHC Control Climate control Lux and temperature sensor LK FUGA. Used to measure the Lux value and temperature for use by IHC Control system. Calcd for flush mounting in boxes for brick wall, and concrete walls- and for front mounting, can for lightweight partition walls and on the underlay

IHC Control Controller accessory antenna splitter. Used to connect two or more antennas to an IHC Controller. This can improve coverage by an IHC Wireless installation.

IHC Control siren - internal - white - for FUGA

IHC Control Input 230 V AC with 8 inputs. Are used as input devices for the 230 V AC. signals from sensors and power control pressure to the IHC system. The module is particularly useful in installations in which the control pressure from the existing high voltage installation to be used for operating a system IHC. Two modules can be connected in series such that the 16 inputs can be connected to one input port IHC. It is possible to place the input module 230 V at both central and decentralized controller in the installation.

IHC Control output 24V DC with 8 outputs. Used for coupling of 8 pieces. 12-48 V d.c. loads, for example. Heat sink elements, LEDs, tales and operating systems.

IHC Control Alarm magnetic contactset for screeded mounting in doors and windows

MultiTouch Pro is a wall mounted touchscreen for operating KNX systems. MultiTouch Pro allows you to control general room functions like temperature, blinds, lighting and scenarios with an intuitive user interface that uses the familiar mindset from smartphones and tablets. Scrolling between the individual functions is done by “swiping" with your finger and on each function, you can choose between operations as push buttons, vertical slide-function, rotary-function or combination. This means that the interface display is always optimized, depending on user requirements and can be reconfigured at any time. You can activate the most used function with a simple hand gesture and in sleep mode, the display can be turned off completely or display a picture, for example a company logo.

IHC Control Alarm backup incl. accumulator 12 V. When the backup module and battery is coupled with IHC Control Alarm, the accumulator will ensure that IHC alarm system is fully operational, even if the network power supply should drop out. Backup module constantly makes sure that the battery is charged to full capacity (12 V, 2.2 Ah). The module must be used with 72 W power supply. Backup module in the front fitted with a 12 V OK lamp indicating that the accumulator voltage is in order. A 24 V OK lamp lights up when the supply voltage is connected. At power failure the module will deliver 24 V for controller, smoke sensor and the input and output modules included in the alarm system. Besides providing module 12 V to gas sensor alarm PIR or other 12 V components. The accumulator is sealed and placed in the bottom of the panelboard. Warning sign for affixation to the panelboard included.

IHC Control 1-10 V converter. Used with an IHC Wireless dimmer to control the brightness of lighting equipment mounted with 1-10 V ballasts.

IHC Control alarm accumulator module - 12 V/2.2 Ah

IHC Control USB cable - 2 meters - black

IHC Control input 24 V DC 3mA with 16 inputs. Used to collect the signals from the low-current contacts with low contact resistance, for example. alarm PIR, thermostats, magnetic switches and other signal generators with long lasting finish functions. Note! OPUS / FUGA PIR can not be used for this input module. To IHC system can be considered a low voltage system, it is a requirement that the used switches are insulated to double insulation (8 mm creepage distance) relative to the 230 / 400V network. It is possible to place the input module 24/3 both central controller and by a decentralized, distributed in the installation.

IHC Control Twilight switch standard. Used for automatic light control, for example. parking lots, walkways, entry lighting, etc. depending on the ambient light level. Location: It is recommended to place the twilight switch so that it is not exposed to direct sunlight / light sources.

IHC Control Climate control Humidity and temperature sensor LK FUGA. Used to measure moisture level and temperature for use of the IHC Control system. Designed for floor recessed mounting in boxes for wall-mounting, molding and for front-loading, can for wall-mounted walls, light-wall-mounted partitions as well as on substrates and panel substrates.

IHC Control Climate Control Temperature Sensor LK FUGA. Used to measure the temperature in the room and / or floor for the use of IHC Control system. Calcd for flush mounting in boxes for brick wall, and concrete walls- and for front mounting, can for lightweight partition walls and on the surface box and floor panel box.