Alupex-järjestelmät - sivu 24

Henco putkisuoristin 20 mm alu-pexille

Uponor 1070556 putkiliitin Puristusta vähentävä

Uponor 1070554 putkiliitin Puristusta vähentävä

Uponor 1070593 putkiliitin Puserrus T-liitin

Uponor 1070540 putkiliitin Kyynärpää

Uponor 1013894 putkiliitin Työntöliitin

Uponor 1029131 putkiliitin Hanasovitin

Geberit Mepla sovitin Geberit Mapressiin, sileällä päädyllä: CC499K, d=32mm, d1=28mm.

Pre-coupling PPSU Uponor 32 mm

Geberit Mepla liitin: d=32mm

Geberit Mepla T-piece with female thread: d=40mm, Rp=1/2, d1=40mm

Geberit Mepla bend adapter 90° with female thread: d=32mm, Rp=1

Geberit Mepla elbow: 45°, d=50mm

Geberit Mepla elbow: 90°, d=63mm

Geberit Mepla kyynärpää: 90°, d=32mm

Paineliitin käyttöveden ja patterijärjestelmien liittämiseen. PPSU-muovia, jossa on ruostumattomasta teräksestä/alumiinista valmistettu painekorkki, vuotamaton jos ei ole painettu oikein. Kalibrointivapaa. Tarkoitettu vain Uponor MLC-putkien kanssa käytettäväksi Uponor-hyväksytyillä puristustyökaluilla.

Presvinkel PPSU Uponor 90° 25 mm

Raxofix T-piece with SC-Contur- silicium bronze- press connectorsd1: 20, d2: 16, d3: 20

Raxofix Adapter elbow 90° with SC-Contur- silicium bronze- press connection, R-threadd: 32, R: 1

Raxofix Adapter elbow 90° with SC-Contur- silicium bronze- press connection, Rp-threadd: 32, Rp: 1

Raxofix Coupling with SC-Contur- Silicium bronze - press connection d1: 40, d2: 40

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Uponor 1029142 putkiliitin Hanasovitin

Raxofix Adapter with SC-Contur- for all Viega metallic systems- silicium bronze- press connectorsComponentsEPDM sealing elementd1: 16, d2: 15

HENCO 26x26 mm VISION työntökyynärä 90 astetta vesi-, lämmitys- ja jäähdytysasennuksiin, enintään 16 baarin paineelle.