Paineputket ja liittimet - sivu 43

Reducer w/ plend cst d35-28 zn-pl

Geberit Mapress FZ El-forzinket

Til varmeanlæg og afkølingPresseindikatorUtæt ved manglende presningFrem- og tilbageløb kan skiftesUdvendigt forzinketT...

...

Viega 1117.2

VSH 45 asteen mutka liitin/liitin 108 mm fz.

For sanitary facilities and industry, for heating systems, cooling and industry.

The Geberit Mapress electro-galvanized press fitting system can be used for joining pipes in closed hot and cold water systems as well as sprinkler systems, fire-fighting water pipes and compressed air networks. Mapress electro-galvanized fittings are made of unalloyed steel. The press joining of pipes and fittings must be carried out with press jaws with an M-profile. When pressing, the pipe is inserted into the press fitting to the marked insertion depth and is thus pressed together.

Please note that Geberit Mapress pipes should be cut to size with a regular pipe cutter before use, and then deburred both inside and outside with a suitable deburring tool. Cutting and deburring are important precisely to avoid damage to the O-ring when the pipe is inserted into the press fitting.

Viega 1115.1

Viega 2318

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Profipress G T-piece with SC-Contur- gunmetal- press connectors, Rp-thread- polygonComponentsHNBR sealing elements d1: 28, Rp: 12, d2: 28

Profipress G T-stykke med SC-Contur- kobber- prestilslutningMedHNBR pakningerd1: 28, d2: 22, d3: 28

Profipress G Coupling with SC-Contur- copper - press connectors Components HNBR sealing elements d: 42

XPress Carbon T-liitin FFF 76,1

XPress ruostumaton suora liitin FM 15XR1/2

XPress ruostumaton suora liitin FF 18XRp1/2

For heating systems, cooling and industry For climate technical areas For sprinkler systems (wet) Not suitable for drinking water pipes.

Viega 1165

Sanpress Inox Adapter with SC-Contur- steel non-corroding- press connection, R-thread Components EPDM sealing element, polygon, VdS certificationd: 22, R: 1

Sanpress Inox Adapter elbow 90° with SC-Contur- steel non-corroding- press connection, Rp-threadComponentsEPM sealing element, VdS certificationd: 22, Rp: 34

Bendad mt cst 90g d28-r1 zn-pl

For heating systems, cooling and industry
For climate technical areas
For sprinkler systems (wet)
Not suitable for drinking water pipes

For sanitary facilities and industry, for heating systems, cooling and industry.

HDMI-jatkokaapeli Ethernetillä, HDMI uros to HDMI naaras, 2 m, musta, ympyrä, 4K-tuki

T-piece ft cst d35-rp3/4-35 zn-pl

For heating systems, cooling and industry
For climate technical areas
For sprinkler systems (wet)
Not suitable for drinking water pipes.