Salus - sivu 2 - Laatua kilpailukykyiseen hintaan

Salus WLS600 water leak detector

The WLS600 leak detector can detect if water occurs and thus connect the sensors to the sensor. The WLS600 must be connected to the Salus Smart Home App via the UGE600 Gateway, thereby allowing you to receive an SMS or mail if water is detected under the sensors. The WLS600 can be set via the app to work together with a Smart Relay or Smart Plug, which can possibly close a valve. 2 meter sensor cable included.

66,01 € (52,60 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Smart home hardwired repeater

Smart Home RE600 is a repeater that connects wirelessly to your Universal Gateway so it becomes an integral part of your Smart Home system. The RE600 can be used if you have an area in the house where there is a bad signal from your Universal Gateway, or if the range is insufficient.

92,01 € (73,32 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Thermostat HTR-RF20

Wireless Thermostat with knob

91,01 € (72,52 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Charging stand CDEUWB

Quantum Charging Dock EU Plug White Box.

88,01 € (70,13 €)

Tilaustuote, 3-6 arkipäivää toimitukseen

Salus Paired floor heating 2 zones FG-2

Salus under floor heating system paired and ready for use - 2 zones.

349,15 € (278,21 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Pump A+Rated 6m 130mm

Salus cirkulation pump, A+Rated, 6m, 130 mm

180,90 € (144,14 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Floor heating manifold 6 slings with flowmeter

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

248,00 € (197,61 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Floor heating manifold 8 slings

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

290,00 € (231,08 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Floor heating manifold 10 slings

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

354,00 € (282,07 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Floor heating unit GVU 2 slings

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

591,97 € (471,69 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Paired floor heating 7 zones FG-7

Salus under floor heating system paired and ready for use - 7 zones.

659,91 € (525,83 €)

Tilaustuote, 10-13 arkipäivää toimitukseen

Salus Floor heating manifold 3 slings with flowmeter

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

162,70 € (129,64 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Floor heating manifold 2 slings

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

128,84 € (102,66 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Mounting box for smart home relay

A mounting box in a nice and timeless design. If it is not possible to build Salus Smart relay into the wall, the mounting box can be used to mount Salus Smart relay on the wall.

16,00 € (12,75 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Paired floor heating 5 zones FG-5

Salus under floor heating system paired and ready for use - 5 zones.

535,61 € (426,78 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Floor heating unit GVU 8 slings

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

854,72 € (681,05 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Floor heating manifold 5 slings

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

189,00 € (150,60 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Floor heating manifold 2 slings with flowmeter

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

128,17 € (102,13 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Floor heating unit GVU 7 slings

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

816,36 € (650,49 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Floor heating manifold 9 slings

SALUS GVM underfloor heating manifold is a high flow distributor with manual balancing of each circuit.Each valve has a built-in manual flow control which is very easy to adjust. Instructions for balancing the circuit can be found in the distributor box.The SALUS GVM manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The inlet- and return- connection is 1 ”thread, and the thread for the actuators are 30 x 1.5 mmContains:Stainless steel distributor set with valveEurokonus for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting bracket for wall mountingWith individual room temperature control.Salus GVM underfloor heating distributors can be supplied with SALUS wireless control.Properties of Salus Underfloor Heating Manifold:Available with Salus insulation in form-stable EPP.Meets the installation requirements for insulation standard DS 452.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.Ready for wall mounting.Can be integrated into the Salus Smart Home solution.Can be operated directly from the room thermostat and from the mobile phone, tablet or computer.The distribution pipes are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension 1 ”for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum proofing pressure: 10 bar

359,00 € (286,06 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Floor heating unit GVU 5 slings

SALUS GVU is a complete floor heating shunt solution for underfloor heating with underfloor heating manifold, shunt and circulation pump built together in one unit.Our circulation pump is a 6m pump with capacity up to 16 zones. The underfloor heating manifold is a high flow manifold with manual balancing of each circuit. Each valve has a built-in manual flow control which is very easy to adjust. Instructions on how to balance the circuit can be found in the distributor box.The SALUS GVM floor heating manifold has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. The Inlet thermostat has a temperature setting of 20 to 55 degrees Celsius. Manifold pipe connection is 1 ", and connection to water for the heat supply is 3/4" socket, and threads to the actuator are 30 x 1.5 mm.

737,91 € (587,98 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus TVR10RAM actuator for Ra-valve

Wireless actuator for radiator valves customized for RA radiator valve for Salus iT600 heating system.

70,01 € (55,79 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Salus Paired floor heating 3 zones FG-3

Salus under floor heating system paired and ready for use - 3 zones.

411,30 € (327,73 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus 24 V wiring centre

24 V Wiring Centre for iT600 Underfloor Heating system

259,01 € (206,38 €)

Tukkurilla, 4-7 arkipäivää toimitukseen

Salus Floor heating manifold 12 slings with flowmeter

SALUS GVM-F underfloor heating manifold is a high flow manifold with manual balancing of each circuit.Each zone valve has on the flow pipe a flow meter that can be used for balancing. Alternatively, the built-in manual flow control integrated into the return valve on the return pipe can be used for balancing. Instructions on how to balance the circuit can be found in the distributor box.SALUS GVM-F underfloor heating distributor has a manual vent on each pipe and a drain valve with 1/2 ”thread for hose. Inlet and return pipe connection is 1 ”thread, and the actuator thread is 30 x 1.5 mmContains:Stainless steel manifold set with flow meterEuroconus set for 20 mm PEXVentilation valve on inlet and returnSwivel filling and drain valveMounting brackets for wall mountingWith individual room temperature control. SALUS GVM-F benefits are available with SALUS - wireless control.Properties:Available with SALUS insulation in form-stable EPPComplies with the installation requirements for insulation standard DS 452.Ready for wall mounting.Can be used with water / glycol mixtures with a mixing ratio of up to 30%.Euroconus are included for all inlets and outlets for 20 mm PEX / PE-RT pipe.• Can be integrated into the SALUS Smart Home solution.Can be operated directly from the room thermostat or from the mobile phone, tablet or computer.Benefits are made of stainless steel alloy AISI304 L Premium quality and extruded in dimension1 ”, for optimal distribution and minimum pressure drop.Maximum working pressure: 6 BarMaximum test pressure: 10 bar

536,12 € (427,19 €)

Tukkurilla, 3-6 arkipäivää toimitukseen

Maanantai - Perjantai	10.00 - 16.00
Lauantai, sunnuntai & Tanskan pyhäpäivät:	Suljettu
Huom! Suljettu perjantaina 5.6.2026
Ota meihin yhteyttä