Reducer - copper - plug-in end, soldered connection d1: 12a, d2: 10

T-piece - copper - solder connection d1: 18, d2: 18, d3: 15(quality seal for d12-54)

Sovitin kyynärpää 90° - messinki - juotettu liitos, R-kierre d: 22, R: 34

Elbow 90°- copper- soldered connection, plug-in endd: 28

Kyynärpää 90° - kupari - juotettu liitos d1: 12, d2: 12

Viega 3130

Viega 3280

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon.

Press connector system with press connectors and pipes made of copper in acc. with EN 1057 and DVGW worksheet GW 392 suitable for:•Gases in acc. with DVGW G 260 in gas installations in acc. with DVGW-TRGI 2008 (DVGW worksheet G 600) / DVFG-TRF 2012•Liquid gas in the gas phase for domestic and commercial applications, tested in acc. with DVGW worksheet G 5614•Heating oil pipelines for heating oil in acc. with DIN 51603-1•Diesel fuel pipelines for diesel fuel, as suction and pressure pipelines in acc. with EN 590 in consideration of the general technical approval Z-38.4-71Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet G 5614, point 4.4.1, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingYellow dot, yellow rectangle and inscription »Gas MOP 5 / GT1«Sealing elementsHNBR, yellowDimensions/MaterialStandard sizes: d 12, 15, 18, 22, 28, 35, 42, 54 made of copperXL sizes: d 64.0 made of copperPress connectors with threaded connection d 12–54 made of gunmetalXL press connectors with threaded connection d 64.0 made of copperAreas of applicationNatural gas/Liquid gasHeating oil/Diesel fuel (d 12–54)NoteOnly Viega copper and gunmetal press connectors, which are marked with a yellow rectangle and have the inscription »Gas MOP 5 / GT1« are permitted for use in installations for gas, heating oil and diesel fuel systems!Use of the system for application areas and media other than those described here must be agreed with Viega Service Center through a material request.Operating conditionsGas and liquid gas systems•Operating temperature -20 °C up to +70 °C•Operating pressure max. 0.5 MPa•Operatin

Prestabo T-piece with SC-Contur- non-alloyed steel, galvanised- press connections, Rp-threadComponentsEPDM sealing elements, polygon

Nipple pipe- gunmetal- G-thread.

Sovitin - asemetallia - juotettu liitos, R-kierre d: 12, R: 38

Viega 95001A

Extension- gunmetal- R-thread, Rp-thread

Pitkä nippa asemetallista R-kierroksella. R: 34, L: 150 mm.

Kyynärpää 45° - kupari - juotettu liitos: 28 (laatuleima d12-54)

Pitkä nänni- asemetalli- R-kierre

Viega 95002A

Viega 2316XL

Easytop ball valve with SC-Contur. Pressure connection. With silicon bronze valve body according to DIN 50930-6 / DIN EN 1982, maintenance-free spindle, T-shaped handle with replaceable medium marking green/red, stainless steel ball, EPDM gaskets (press connection).

Easytop circulation regulation valve S/Ethermostatical regulation valve, with SC-Contur

Sanpress XL Reducer with SC-Contur- gunmetal- plug-in end, press connectionComponentsEPDM sealing element, cutting ringd1: 88.9, d2: 76.1

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Waterproof connection socket for flexible Polybutene.- not suitable for PE-X/AI/PE-X, PE-Xc- gunmetal- Rp-thread- soundproofingWith angle in gunmetal, pressure test nozzleModel 5330

Or the specified areas of application and operating conditions. Any use outside of these must be agreed with Viega Service Center.