Unidrain Viemäröinti - sivu 6

Ensures correct positioning and fixing of the drain unit in wooden floor joist structures. Adjust to the correct length by cutting the front profile.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Can be freely positioned against the back wall, independent of any side walls. The rear flange has been moved 12 mm backwards, to fit 15 -20mm wall tiles + tile mortar + wetroom membrane.

NB! ClassicLine or HighLine frame must be used.

For testing of the wetroom solution for leaks before laying tiles. Placed in the drain unit. Fill the shower niche with 20-mm water and allow to stand for 24 hours to test the seal.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Choose between two models. A panel completely without frame, or the model with panel including frame.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

Water trap for corner outlet houses 2001.

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Rist Unidrain pylväs 1602 on 1200 mm pitkä.