Työkalut putkitöihin - sivu 5

REMS Solar-Push K 60. Electric filling and flushing unit for easy and quick filling, flushing and venting of closed systems. In carton. Transport performance = 36 l/min., container volume 30 l. With centrifugal pump, temperature resistant for constant load = 60°C. Shipping pressure = 5.5 bar/0.55 MPa/80 psi. Condenser motor 230 V, 50 Hz, 860 W. 2 pcs. flexible, transparent woven PVC hoses 1/2" T60, each 3 m long, temperature resistant = 60°C.

Bahco 301-22 putken ja letkun leikkuulaite

Specially hardened and specially ground blade, exchangeable, PTFE-coated.German quality product

PUTKILEIKKURI 35 DURAMAG (Cu, messinki, Al, ohutseinämäinen putki)

Puhdistus kupariputkille ja muoviputkille, jotka ovat lyijykynän muotoisia ja siksi helppo kuljettaa taskussa.

Ridgid 117 miniputkileikkuri

High compression pressing tongs/pressing rings in forged and specially hardened steel. Pressing contours of REMS pressing tongs/pressing rings are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC & REMS Mini-Press 22V ACC drive units. Read and follow the installation and assembly instructions of the system provider/manufacturer.

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.

KNIPEX 00 11 02 Sähkökaapin avain tavanomaisiin kaappeihin ja sulkujärjestelmiin 44 mm

Pyörä, leikkuri e4546 105/205 hd

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.

REMS pressing tongs Mini Very compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs Mini with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the g after the pressing process. This enables the user to check again whether the most suitable pressing tongs have been used to make the pressfit connection even after the pressing process.With this traceability REMS fulfils the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

Ridgid putken taivutin 315m

KNIPEX 87 21 250 SB Cobra® QuickSet Hightech-vesipumppupihdit pinnoitettu liukumisen estävällä muovilla fosfatoitu harmaaksi 250 mm (Piikkipakkauskortti/muovipakkaus)

REMS Frigo 2 F Zero. Electric tube freezer with closed refrigerant circuit. For steel, copper, plastic and plastic pipes with metallic insert Ø 1/8–2", Ø 10–60 mm. Cooling unit 230 V, 50 Hz, 430 W, 2 coolant hoses, 2 clamping bands, spray bottle. Equipment for Ø 1/4"–1 14", 15–42 mm. In stable steel cabinet. Internal refrigerant: R290.

KNIPEX 81 13 250 Sifon- ja liitinpihdit pinnoitettu liukumisen estävällä muovilla kromattu 250 mm

REMS cutter wheel Cu-INOX for stainless steel pipes of pressfitting systems, copper, carbon steel

REMS cutter wheel Cu-INOX for stainless steel pipes of pressfitting systems, copper, carbon steel

Power-transmitting pipe holder. For assembly and demolition. Unique pipe holder that 5 times the power transfer – allows easy, fast, perpendicular sawing on site, without the use of a vise. Ideal handling, easy and quick operation, just one handle for clamping and sawing. No freely swinging chain and cumbersome operation, as when using a chain vise. No clamping option, as the swing angle is limited. 400% more sawing power available for a power-saving, super-fast sawing during assembly and demolition, e.g. a 4" steel pipe in just 8 seconds. With the pipe holder installed, for optimal sawing, it is recommended to use a straight hand grip.

Juotosimuri HQ
kevyt metallikotelo, jossa on antistaattinen Teflon-kärki

Specially hardened cutter wheel in approved, tough-hard REMS die-steel quality ensures a long service life.REMS cutter wheel Cu-INOX 3 – 120, s 4Copper tubes, stainless steel tube

Helppo viistäminen PE-putken pää ennen asennusta puristusliittimiin.

KNIPEX 87 02 250 Cobra® Hightech-vesipumppupihdit hoikilla monikomponentti kahvakuorilla fosfatoitu harmaaksi 250 mm

KNIPEX 88 01 250 SB Alligator® Vesipumppupihdit pinnoitettu liukumisen estävällä muovilla fosfatoitu mustaksi 250 mm (Piikkipakkauskortti/muovipakkaus)