Unidrain - sivu 19

Rist Unidrain klassinen kulma 3 mm.

The water trap is removable and can be taken apart for cleaning.

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

Unidrain-vesilukko ulostulo yksikköön 1418.0050

Ulosottoyksikkö | linja | Ø 50 mm vaakasuora, sisältää vesilukon

Unidrain puinen ritilä kulmaliitoksille.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

The set consists of the Custom base, rail, heightener set and screws.

The set must be assembled before installation.

Glue your own floor tile to the base, to complete the solution.

The Custom solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit.

Special glue for adhesion of your own tile and 10 x 6-mm spacers to use for installation are also included.

Can be freely positioned against the back wall, independent of any side walls. The rear flange has been moved 12 mm backwards, to fit 15 -20mm wall tiles + tile mortar + wetroom membrane.

NB! ClassicLine or HighLine frame must be used.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

With side drain on the left.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

Horizontal outlet Ø 75 mm, including water trap.

Two horizontal side inlets, 40 mm, which can be opened as needed. 2 rubber adapters are included so that side inlets can be reduced to 32 mm. Easy access to the removable water trap for cleaning. Meets EN1253 standard and is VA approved.

Hook to lift the water trap up from the outlet unit.Suitable for use with line and corner models.

Lattiakaivo Unidrain 1001, 1200 mm.

Raastin Unidrain classic 1601, jonka pituus on 300 mm.

Unidrain Highline RS 800 -paneeli

The water trap is removable and can be taken apart for cleaning

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.