Viega - sivu 39

Screw fitting- gunmetal- R-thread, Rp-thread- conical sealing

Sanpress T-piece with SC-Contur- gunmetal or silicium bronze- press connectorsComponentsEPDM sealing elements d1: 28, d2: 28, d3: 28

Press connector system with press connectors made of gunmetal, pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DINEN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene

Coupling- gunmetal- Rp-threadRp: 14

Viega 1118

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Reducer- gunmetal- R-thread, Rp-thread- round

Nänni- asemetalli- G-kierre

Viega 3241

Liitoskyynärpää 90° - WC:lle - muovikomponentit - huulitiiviste DN: 100, versio: alppivalkoinen

Viega 3241

Sanpress Inox Sliding coupling with SC-Contur- steel non-corroding- press connectors ComponentsEPDM sealing elementsd: 15

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.

Sanpress Inox T-piece with SC-Contur- steel non-corroding- press connectorsComponentsEPDM sealing elementsd1: 28, d2: 18, d3: 28

Viega 3121

Viega 95243

Easytop Ball valve with SC-Contur- for water- and heat meter- not suitable for Easytop Insulating shell 2275.90- press connection, G-threadComponentsValve casing gunmetal or silicium bronze according to DIN 50930-6 / DIN EN 1982, maintenance-free selector shaft, black powder-coated actuating lever made of metal, EPDM sealing element, EPDM flat seal.Technical data operating pressure max. 1.6 MPa (PN 16) operating temperature max. 110 °Cwith DVGW-test mark DN: 15, d: 15, G: 34

Sanpress Adapter with SC-Contur- gunmetal or silicium bronze- press connection, Rp-threadComponentsEPDM sealing element, polygon, VdS certification d: 42, Rp: 112

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Raxofix Adapter with SC-Contur- silicium bronze- press connection, Rp-threadd: 25, Rp: 1

Raxofix Coupling with SC-Contur- silicium bronze- press connectiond1: 32, d2: 25

Pipe odour trap - for sink - plastic Components Drain elbow 45°, waste water hose connection Quality controlled in accordance with DIN EN 274 G: 112, DN: 40

Long nipple- gunmetal- R-thread

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings – DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site – hempen without roughening of the thread is possible.