PEX-järjestelmät - sivu 4

Päättelylaatikko, joka sisältää Q&E-päätysolmun DR-messingistä, valkoinen Q&E-rengas ja kiinnitysruuvit. Vesitiivis liitäntä PE-Xa-putkien ja Uponor-kanavien kanssa kaikenlaisissa seinissä NT VVS 129:n mukaisesti.

Transition from 22 mm to pipe thread.

Uponor 1033974 putkiliitin Päätytaite

Uponor 1008684 putkiliitin Hanasovitin

Uponor 1008666 putkiliitin Hanasovitin

Manifold in gunmetal with push and insert in AISI 316

Used for Roth Quickskab, manifold cabinet

For assembly of pipes or fittings.

For assembly of pipes or fittings.

Used for For pipe in 20 mm

Transition from 15 mm to pipe thread.

Used for Pex and CU pipe

Roth QuickBox®-316 for stonewall,18 mm x 3/4" push, db

Henco-liitoshaara, jossa on 2 x 3/4 eurocone ja 1 x kierteellinen pää.

Fitting in gunmetal for Roth manifold

Fitting in gunmetal for Roth manifold

Quickbox tool for flange

used for Roth gunmetal manifold

Työkalu seinän laippaan

Nipple in gunmetal Roth 3/4" EURO x 3/4", used with female plastic pipe fitting

Uponor 1001337 putkiliitin Putkitulppa

Transition from 15 mm to pipe thread.

For dry wall, push

Kipsilevyasennussarja seinälaatikkoon

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f