PEX-järjestelmät - sivu 5

For assembly of pipes or fittings.

Intake Piece for pipe systems with QuickBox

Used for For pipe in 34 mm

Fits directly into insertion fitting.

For assembly of pipes or fittings.

PPM-ohjauskeskuksen ripustusklipsit asennettavaksi ohjauskeskuskoteloon. Valmistettu PPSU:sta.

For dry wall, push

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Uponor 1008661 putkiliitin Hanasovitin

Roth QuickBox®-316 for stonewall,18 mm x 3/4" push, db

Manifold in gunmetal with push and insert in AISI 316

used for Roth gunmetal manifold

Transition from 22 mm to pipe thread.

Slip coupling, push-fit 15mm stainless steel

For assembly of pipes or fittings.

Päättelylaatikko, sisältäen päättelykyynärän DR-messingistä ja kiinnitysruuvit. Vesitiivis liitäntä PE-Xa-putkien ja Uponor-kanavien kanssa kaikenlaisissa seinissä, NT VVS 129:n mukaisesti.

Transition from 22 mm to pipe thread.

Uponor 1008663 putkiliitin Hanasovitin

Wallofix seinärasia pitkä TT 15 mm

HENCO VISION messingistä valmistettu holkkiadapteri 26 x 3/4 jakoputkille vesi-, lämmitys- ja jäähdytysasennuksiin. Max. 16 bar.

For assembly of pipes or fittings.

Seinäteline 3/4" haaraputkelle, sarja 2 kpl

Polyeteenieriste Pettinaroli-vedenjakeluputkelle CC50. Sopii 4 ympyrään ja voidaan helposti leikata tarvittaessa. Huomio: voidaan käyttää vain CC50:lle eikä CC35:lle.

Or the specified areas of application and operating conditions. Any use outside of these must be agreed with Viega Service Center.

Uponor 1038037 putkiliitin Kyynärpää