Rems Työkalut putkitöihin

Li­Ion PLUS technology. Highly resistant Li­Ion 14.4 V Powerful and light. Total discharge and overload protection with single cell monitoring. Temperature monitoring during the charging process. Operating temperature range –10 to +60 °C. No memory effect for maximum battery power.

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS Akku-Press 22 V ACC Basic-Pack
Electro-hydraulic battery radial press with automatic return and press pressure monitoring for the production of press joints for all common press fitting systems.
Li-Ion 22 V Technology.
Pipe press joints Ø 10 – 108 (110) mm, Ø 3/8 – 4"
"M" press 12 - 54 mm

With automatic return and press pressure monitoring.
Anti-vibration system.
Safe pressing result in a few seconds.
Automatic locking of the press bar.
Battery Li-Ion 21.6 V, 2.5 Ah for approx. 200 presses of Viega Profi press DN 15 per battery charging.

For operation of REMS press bars/press rings and for suitable press bars/press rings of other makes.
Rotatable press bar attachment with automatic lock.
Electro-hydraulic drive with powerful battery motor 21.6 V, 380 W.
Anti-vibration system.
Safety switch.
LED work lamp.
Battery Li-Ion 21.6 V, 2.5 Ah, fast charger Li-Ion 230 V, 50 – 60 Hz, 90 W

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

Robust quality tools for cutting tubes. Particularly suited for cutting stainless steel tubes.Copper tubes, thin-walled stainless steel tubes, thin-walled steel, aluminium, brass tubes Ø 6 – 35 mm Ø 18 – 138REMS RAS Cu-INOX – the compact version with telescopic spindle.

Light, portable compact machine. Universal for cutting and deburring pipes. For trade and industry. For the building site and the workshop.Stainless steel pipes of pressfittingsystems, carbon steel, copper Ø 8 – 108 mmSteel pipes EN 10255 (DIN 2440) DN 10 – 100 Ø 14 – 4, Ø 14 – 115 mmCast iron pipes (SML) EN 877 (DIN 19522) DN 50 – 100Plastic pipes SDR 11 Wall thickness s 10 mm Ø 10 – 110 mmMultilayer composite pipes Ø 10 – 110 mmREMS Cento – Cutting and deburring up to Ø 115 mm. Super fast. Right angled. Chip-free. No outer burr. Dry cutting. Universal for many pipe types.

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

Hand pressure test pump with manometer, p = 60 bar/6 MPa/870 psi, for pressure and tightness testing of pipe systems and containers up to 60 bar/6 MPa/870 psi. Corrosion-resistant, powder-coated steel container for 12 l volume. 1.5 m high-pressure hose with 12" connection. In carton.

Proven hand unit for quick application to remove pipe blockages in kitchen, bath, toilet.For pipes Ø 20–50 (75) mm. For cables Ø 6, 8, 10 mm.REMS Mini-Cobra – by hand or electric.Indispensable to remove small blockages.

REMS Frigo 2 F Zero. Electric tube freezer with closed refrigerant circuit. For steel, copper, plastic and plastic pipes with metallic insert Ø 1/8–2", Ø 10–60 mm. Cooling unit 230 V, 50 Hz, 430 W, 2 coolant hoses, 2 clamping bands, spray bottle. Equipment for Ø 1/4"–1 14", 15–42 mm. In stable steel cabinet. Internal refrigerant: R290.

Universal, handy electric tool with automatic circuit control for producing pipe pressing joints for all common pressfitting systems. For battery and corded operation. Pressing joints Ø 10–108 mm / 3/8 - 4. Complete range of REMS pressing tongs/pressing rings for all common pressfitting systems.REMS Akku-Press ACC Li-Ion – universal up to Ø 108 mm / 4.With automatic circuit control and electronic service control. Secure crimping in seconds. Automatic locking of pressing tongs

Powerful, easy-to-operate electric tool for threading with unique support bracket. Ready for use anywhere, without vice. Ideal for repair, renovation, job site.Pipe threads 18 – 114, 16 – 40 mm Bolt threads 6 – 30 mm, 14 – 1Set includes Die heads R 12 - 34 - 1 - 114REMS Amigo – the smallest, lightest, strongest and fastest up to 114.

REMS pressing tongs MiniVery compact design and low weight of the REMS Mini pressing tongs due to special arrangent of the pressing tongs connection (Patent EP 1 952 948).High compression pressing tongs/pressing rings in forged and specially hardened steel. Pressing contours of REMS pressing tongs/pressing rings are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC drive unit. Read and follow the installation and assembly instructions of the system provider/manufacturer.

REMS cutter wheel St for steel pipes, cast iron pipes (SML)

Powerful, electric pressure testing pump for pressure and tightness tests of piping systems and receptacles. Testing and pressure range p 60 bar/6 MPa/870 psi. Pumping capacity 6.5 l/min water, hydrous solutions, emulsions, ph-value of liquids 7-10, temperature of liquids 60°C, viscosity of liquids 1.5 mPa s.REMS E-Push 2 – electric charging and testing. Up to 60 bar. With adjustable pressure limiting. 1300 W. Self sucking.

REMS Solar-Push K 60. Electric filling and flushing unit for easy and quick filling, flushing and venting of closed systems. In carton. Transport performance = 36 l/min., container volume 30 l. With centrifugal pump, temperature resistant for constant load = 60°C. Shipping pressure = 5.5 bar/0.55 MPa/80 psi. Condenser motor 230 V, 50 Hz, 860 W. 2 pcs. flexible, transparent woven PVC hoses 1/2" T60, each 3 m long, temperature resistant = 60°C.

Powerful, handy cordles battery tool for cutting pipe and tubing. For trade and industry. For the building site and the workshop.Stainless steel pipes of pressfittingsystems, carbon steel, Ø 12 – 28 mmcopper Ø 10 – 35 mmMultilayer composite pipes Ø 10 – 40 mmREMS Akku-Nano – cutting up to Ø 40 mm. Ultra-light. Fast. Right angled. Chip-free. Without outer burr. Dry.

REMS pressing ringsHigh compression pressing rings in forged and specially hardened steel. Pressing contours of REMS pressing rings are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing segments manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS pressing ringsHigh compression pressing rings in forged and specially hardened steel. Pressing contours of REMS pressing rings are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing segments manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS Tiger ANC VE set. Electric pipe bayonet saw with vario electronics (VE) for easy, fast, perpendicular sawing with pipe holder and for freehand sawing up to 6", 250 mm. Machine with spade handle, maintenance-free, water and dust protected oscillation drive with versatile needle bearing drive (ANC) , aggressive orbital stroke, 230 V, 1050 W, safety rocker switch. Universal saw blade holder for 2". 2 REMS special saw blades 2". In a stable steel case.

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.

REMS cutter wheel Cu-INOX for stainless steel pipes of pressfitting systems, copper, carbon steel

REMS pressing tongs High compression pressing tongs in forged and specially hardened steel. Pressing contours of REMS pressing tongs are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour. Hence far closer tolerances compared to as cast pressing contour.Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable radial presses of other makes. Read and follow the installation and assembly instructions of the system provider/manufacturer.Traceability according to EN 1775:2007 REMS pressing tongs/pressing rings with pressing contour M, V, SA, B, RN and UP have worked a specific marking into the pressing contour which leaves a lasting impression on the pressed fitting after the pressing process. This enables the user to check again whether the most suitable pressing tongs or the suitable pressing ring have been used to make the pressfit connection even after the pressing process.With this tracability REMS fulfills the recommendations of the European standard EN 1775:2007 for the installation of pressfitting systems for gas.

REMS Sanitol – mineral oil free. Completely water soluable. High lubricating and cooling effect.Synthetic, mineral oil free thread-cutting oil. Specially for drinking water supplies. Also for universal use. For all materials.

High compression pressing tongs/pressing rings in forged and specially hardened steel. Pressing contours of REMS pressing tongs/pressing rings are system-specific and correspond with the respective pressfitting system. Thus perfect system-conformity, safe press jointing. Pressing jaws of pressing tongs manufactured on CNC production centres ensure high-precision machining of pressing contour.Drive through REMS Mini-Press ACC & REMS Mini-Press 22V ACC drive units. Read and follow the installation and assembly instructions of the system provider/manufacturer.