Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

Flex frames are used to extend the floor drain’s visible length. They are laid endto-end to the frame, using tile mortar, so there is no need to cut small pieces of tile.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

HighLine Panel, Cassette or Custom must be selected.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

With side drain on the right.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

With side drain on the right.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

Complete square drain set. Package includes ClassicLine Column grating and frame 15×15 cm, steel drain unit, flow guide, water trap, outlet unit Ø 75 mm horizontal with side inlets, 3 x adapters (2 pcs. for 40 mm pipes and 1 pc. for 32 mm pipe). The height of the unit can be adjusted +/- 10 mm and rotated 360° in the outlet unit. Truncate the ClassicLine frame to tile level. Minimum tile layer 8 mm. Cleaning cloth included.

HighLine Color on valmistettu PVD-käsitellystä ruostumattomasta teräksestä. Runko on yhdistettävä paneeliin.

Highline-kehys - Harjattu teräs 900/10 mm

Outlet-talo unidrain pystysuora EX-ansa Ø50.

Pistorasiakotelot ovat erittäin matalia asennuskorkeudeltaan ja niitä voidaan mahdollisesti yhdistää VA-hyväksytyn hajuesteen kanssa. Lukituskiinnike varmistaa, että pistorasiakotelo on aina kiinnitetty oikeassa asennossa lattiakaivoon, ja pari jalkaa pistorasiakotelon alaosassa mahdollistavat sen kiinnittämisen perustukseen.

Runko Unidrain 1500 700X12 mm.

Lattiakaivo Unidrain 1001, 1000 mm.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Kiinnityslaite Unidrain 1003, 1000 mm kulma oikealle.

Soap shelf including grating and mounting set. Designed for insertion in tile joint or for mounting in an existing shower cubicle. For corner installation only – applies to both models.

Ansa tiiviste nurkkasijoitukseen sopivalle lattiakaivolle.

Complete square drain set. Package includes HighLine Custom base 10×10 cm, steel drain unit, water trap, outlet unit Ø 75 mm horizontal with side inlets, 3 x adapters (2 pcs. for 40 mm pipes and 1 pc. for 32 mm pipe). The height of the unit can be adjusted +/- 10 mm and rotated 360° in the outlet unit. Special adhesive is included to glue your own tile to the Custom base. Hook and cleaning cloth included.

For shower cubicles without fixed walls.

The drain unit has four floor flanges.

Including four heght-adjustable feet (40-190 mm).

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile).

The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame.

The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

The grating is selected from among six attractive designs.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Four height-adjustable feet (120-220 mm) for installation on concrete.